AG06 / AG03 已停產

必須從網際網路下載該軟體。請尋找下列網址。

是的。AG 支援 ASIO 驅動程式。Windows 上必須安裝 Yamaha Steinberg USB 驅動程式。安裝後，您可以使用支援 ASIO 的 DAW 軟體，例如 Cubase AI。在 Mac 上，則無需安裝驅動程式。作業系統的的預設驅動程式將起作用。

它支援行動電源 (5V 500mA)，但我們無法保證所有類型的行動電源都能正常工作。

要連接 iPad 和 AG 系列產品，需要下列項目。

- 相機連接套件或 Lightning-USB 相機配接器

- 行動電源 (5V 500mA，並連接到混音座上的 Micro USB 端口) 供電

基本上功能上沒有差異。主要區別在於 I/O 連接器的數量以及控制開關和旋鈕的類型和數量。

It is the switch to lower the input signal level. Please turn it on when the input signal is distorted or the level is too high.

It is the switch to turn on/off for the equalizer and the compressor which can adjust the sound quality and minimize the variation on volume respectively.

It is necessary to install the USB driver to connect the console to PC. To install the USB driver, please refer to the following.

The audio signal input to Ch 1 & 2 (Ch 2G for AG03) will be sent to the connected PC/iPad directly with the USB. These signals will not be affected by the level knob/fader. Also, the signal input to ch 1 & 2 can be recorded seperately.

The audio signal that input to the console and mixed on stereo will be sent to PC/iPad. The input signal from computer will not be sent.

The audio signal input to the console and the playback on the computer will be mixed on stereo and send to PC/iPad. Mainly for using on internet casting.

When the MONITOR MUTE is switched on, the audio signal input to Ch 1 & 2 (Ch 2G for AG03) will no longer be able to output from the output port on console.

It is only that the signal will not output from the output port, but will still be able to send to the PC/iPad. It is usually used when direct monitoring is not necessary.

Adjust the volume of AUX on the connected devices.

Connect the console to the optional footswitch(Yamaha FC-5, etc) and switch on the EFFECT button allows the user tp mute the effects with foot.

Please check if the mic input of the headset is pluged in (with any device)? Ch 1 & Headset mic cannot be used together at the same time. Headset Mic input has higher priority.

Please check if the output port for headset is pluged in (by any device)? The headphone output on the top right corner of the console and headset output cannot be used together at the same time. Headset output has higher priority.

The audio signals are looping.

To fix this, you may use the following methods.

For DAW: Please set the TO PC switch to DRY CH1-2(G) or INPUT MIX (not LOOPBACK).

For Webcasting software: Turn off the monitor switch on the webcasting software.

The audio signals from PC and console are overlaped.

To fix this, you may use the following methods.

For DAW: Switch on MONITOR MUTE.

For Webcasting software: Turn off the monitor switch on the webcasting software.

Please check if the GAIN level is too high. Or the PAD switch is on by mistake. Also, please try to speak onto the mic.

Press the [MONITOR MUTE] switch to turn on. [MONITOR MUTE] switch prevents duplex sound when user is broadcasting over the internet. However, the noises from headphones can be attenuated with turning on [MONITOR MUTE] switch. If [MONITOR MUTE] switch is turned on, the sound of CH1 and CH2 (only the case of 2G GUITAR switch is turned on for AG03) will not be heard.

Please install AG DSP Controller to adjust the parameters of the EFFECT. There is only ON/OFF switch on the console.

It is allows to use the AG Guitar Amp Simulator on AG DSP Controller to turn on/off and adjust the parameters for AMP SIM function.

Please check if the Guitar switch on AG06 or GUITAR/LINE switch on AG03 is switched on.

Please check if the Guitar switch on AG06 or GUITAR/LINE switch on AG03 is switched on.

When using AG DSP Controller together with Cubase AI, please start up the AG DSP Controller first.