﻿N3X
Owner's Manual


Assembling the Unit
When assembling the unit, consult a qualified AvantGrand dealer.

CAUTION
Be careful not to confuse parts, and be sure to install all parts in the correct orientation. Please assemble in accordance with the sequence given below.
Assembly should be carried out by at least three persons.
Be sure to use the correct screw size, as indicated below. Use of incorrect screws can damage the instrument.
Be sure to tighten all screws upon completing the assembly of each unit.
To disassemble, reverse the assembly sequence given below.

Have a Phillips-head (plus) screwdriver of the appropriate size ready.

(Figure)

CAUTION
Do not lay the main unit upside down on the floor.

(Figure)
Incorrect

1	Remove the parts and collect them together for assembly.
1-1	Remove the parts shown below from the smaller box.

(Figure)
Legs
Front (L)
Rear
Front (R)
Bolts (17 pcs.)
Screws (4 pcs.)
Pedal
Pedal brace rods (2 pcs.)
Power cord
Cord holders (3 pcs.)
Wrench
(Used to tighten bolts)

1-2	Set the larger box upright with the right side up.

(Figure)
This side down

1-3	Cut the bands.
1-4	Remove the covers.

2	Attach and securely tighten the right front leg and the rear leg with the bolts.

(Figure)
x6
x5

CAUTION
When the instrument is set upright (as in the illustration above), take extra care not to keep the instrument from falling over, since it is unstable in this position.

3	Set a blanket at the left corner.

(Figure)

4	Set the piano upright.

(Figure)

5	Attach and securely tighten the left front leg with the bolts while holding the piano firmly.

(Figure)
x6

CAUTION
Do not hold the control panel. Using excessive force on the panel can result in damage to the instrument.

6	Attach the pedal brace rods.
Find the threaded bores on the bottom of the unit, and securely tighten the screws to attach the rods.

(Figure)

7	Attach the pedal.
Insert the pedal brace rods into the pedal box recesses and make sure they fit securely, then securely tighten the screws to attach the pedal.

(Figure)

8	Connect the pedal cord.
8-1	Make sure the pedal cord is clipped into the cord holder.
8-2	Insert the pedal cord plug into the pedal jack.

(Figure)

9	Connect the power cord.
9-1	Set the voltage selector and insert the power cord plug to the [AC IN] connector.
9-2	Attach the cord holders to the instrument, then clip the power cord into the holder.

(Figure)
[AC IN] connector (page 10)
Voltage Selector
(the bottom of the left side as seen from the front)

Voltage Selector
Before connecting the AC power cord, check the setting of the voltage selector which is provided in some areas. To set the selector for 110V, 127V, 220V or 240V main voltages, use a "minus" screwdriver to rotate the selector dial so that the correct voltage for your region appears next to the pointer on the panel. The voltage selector is set at 240V when the unit is initially shipped. After the proper voltage has been selected, connect the AC power cord to the AC IN and an AC wall outlet. A plug adaptor may be also provided in some areas to match the pin configuration of the AC wall outlets in your area.

WARNING
An improper voltage setting can cause serious damage to the instrument or result in improper operation.

CAUTION
If the main unit creaks or is otherwise unsteady when you play on the keyboard, refer to the assembly diagrams and retighten all screws.

After completing the assembly, please check the following.
Are there any parts left over?
	-> Review the assembly procedure and correct any errors.
Is the instrument clear of doors and other movable fixtures?
	->  Move the instrument to an appropriate location.
Does the instrument make a rattling noise when you shake it?
	->  Tighten all screws.
Is the power cord inserted securely into the sockets?
	->  Check the connection.
Is the pedal unstable? 
	->  Loosen the screws of the pedal brace rods, then tighten the screws again while pushing the rods toward the pedal.



This is the end of the file.