﻿CVP-709/CVP-705 Owner's Manual

CVP-705 Assembly

CAUTION
Assemble the unit on a hard and flat floor with ample space.
Be careful not to confuse or misplace the parts, and be sure to install all parts in the correct orientation. Please assemble the unit in accordance with the sequence described here.
Assembly should be carried out by at least two persons.
Be sure to use only the included screws of the specified sizes. Do not use any other screws. Use of incorrect screws can cause damage or malfunction of the product.
Be sure to tighten all screws upon completing assembly of each unit.
To disassemble the unit, reverse the assembly sequence.

Have a Phillips-head (+) screwdriver of the appropriate size ready.
(Figure)

Remove all parts from the package and make sure you have all of the items.
(Figures)
A
Remove foamed styrol pads from the package, position them on the floor, then place A on top of them. Position the pads so that they will not block the speaker box on the bottom of A.

B
C
Bundled pedal cord inside here.

D
E
F 6 x 20 mm x 4
G 4 x 12 mm x 2
H 4 x 20 mm x 4
J 6 x 16 mm x 6

Power cord
Cord holders x 2

Headphone hanger
K 4 x 10 mm x 2

1	Attach C to D and E.

1)	Untie and straighten out the bundled pedal cord.
Do not discard the vinyl tie. You will need the vinyl tie later in step 5.

2)	Secure D and E to C using four screws F.

(Figure)

2	Attach B.

1)	Align the holes on the upper side of B with the bracket holes on D and E, then attach the upper corners of B to D and E by finger-tightening two screws G.

2)	Secure the bottom end of B using four screws H.

3)	Securely tighten the screws G on the top of B that were attached in step 2-1.

(Figure)

3	Mount A.
Be sure to place your hands at least 15 cm from either end of the main unit when positioning it.

(Figure)
Align the screw holes.
15 cm or further in

CAUTION
Be extra careful not to drop the unit or let your fingers be pinched by the main unit.
Do not hold the main unit in any position other than the position specified here.

4	Secure A.

1)	Adjust the position of A so that the left and right ends of A will project beyond D and E equally as shown in the illustration.

2)	Attach A using six screws J.

(Figure)

5	Connect the pedal cord and power cord.

1)	Insert the pedal cord plug into the pedal connector.
Insert the pedal cord securely until the metal part of the cord plug disappears from view. Otherwise, the pedal may not function properly.
(Figure)

2)	Attach the cord holders to the rear panel as shown, then clip the cord into the holders.

3)	Use a vinyl tie to take up any slack in the pedal cord.

4)	Insert the AC power cord plug into the [AC IN] jack.
(Figure)

6	Rotate the adjuster until it comes in firm contact with the floor surface.
(Figure)

7	Attach the headphone hanger.
Attach the headphone hanger using two screws K as shown in the illustration.
(Figure)

After completing the assembly, please check the following.

Are there any parts left over?
Review the assembly procedure and correct any errors.

Is the instrument clear of doors and other movable fixtures?
Move the instrument to an appropriate location.

Does the instrument make a rattling noise when you shake it?
Tighten all screws.

Does the pedal box rattle or give way when you step on the pedals?
Turn the adjuster so that it is set firmly against the floor.

Are the pedal and power cords inserted securely into the sockets?

CAUTION
When moving the instrument, always hold the bottom of the main unit. Do not hold the key cover or top portion. Improper handling can result in damage to the instrument or personal injury.

(Figure)
Do not hold here.
Hold here.

Transporting
If you move to another location, you can transport the instrument along with other belongings. You can move the unit as it is (assembled) or you can disassemble the unit down to the condition it was in when you first took it out of the box. Transport the keyboard horizontally. Do not lean it up against a wall or stand it up on its side. Do not subject the instrument to excessive vibration or shock. When transporting the assembled instrument, make sure all screws are properly tightened and have not been loosened by moving the instrument.

CAUTION
If the unit creaks or is otherwise unsteady when you play on the keyboard, refer to the assembly diagrams and retighten all screws.

This is the end of the file.