﻿CVP-709/CVP-705 Owner's Manual

CVP-709 Assembly

CAUTION
Assemble the unit on a hard and flat floor with ample space.
Be careful not to confuse or misplace the parts, and be sure to install all parts in the correct orientation. Please assemble the unit in accordance with the sequence described here.
Assembly should be carried out by at least two persons.
Be sure to use only the included screws of the specified sizes. Do not use any other screws. Use of incorrect screws can cause damage or malfunction of the product.
Be sure to tighten all screws upon completing assembly of each unit.
To disassemble the unit, reverse the assembly sequence.

Have a Phillips-head (+) screwdriver of the appropriate size ready.
(Figure)

Remove all parts from the package and make sure you have all of the items.

(Figures)

A
To prevent the key cover from accidentally opening during assembly, press down on the key cover, making sure that the sheets (shown) remain in place.
To prevent damage to the speaker box located at the bottom of unit A, make sure to place unit A on the styrofoam pads. Also, make sure that the pads do not touch the speaker box. 

B
C
D
E

F
Bundled pedal cord inside. The pedals are covered with covers when shipped from the factory. Remove the cover from the damper pedal for optimum use of the GP Responsive Damper Pedal effect.

G

Protective pads x 2
Power cord

H 5 x 30 mm x 4

M 4 x 20 mm x 3

Headphone hanger
P 4 x 10 mm x 2

CVP-709B/CVP-709PE
J, L 5 x 18 mm x 10
N 4 x 10 mm x 2
Q 5 x 15 x 1.2 mm x 4

CVP-709PWH
J (a) (b) (c) (d) x 6
(a) 5 x 20 mm x 6
(b) 6 x 13 x 2.5 mm x 6
(c) x 6
(d) 5 x 16 x 2 mm x 6
K x 8
L 5 x 18 mm x 4
N (a) (b) x 2
(a) 4 x 12 mm x 2
(b) 4 x 13 x 2.5 mm x 2

1	Lean unit A against the wall as shown.

1)	Spread a large soft cloth, such as a blanket, as shown to protect the floor and wall surfaces.

2)	Lean unit A against the wall with the key cover closed and the keyboard side on the bottom.

(Figure)
Large soft cloth
Styrofoam pads
Protective pads
NOTICE
Do not touch the speaker net.
Doing so may damage the speaker inside.

CAUTION
Be careful not to pinch your fingers.

NOTICE
The top part of the music rest is not fixed. Support the music rest with your hand so that the music rest will not fall.
Do not place the main unit upside down or with the rear side facing down.

2	Attach units B and C to unit A.

1)	Align units B and A so that the protrusion fits into the hole.
(Figure)

2)	Fix unit B to the bottom surface of unit A using two screws H. 
(Figure)

Attach the parts, pressing unit B onto unit A so that the two fit tightly together.

3	Fix unit B to the speaker box of unit A using two screws J.
(Figure)

If the screw holes do not align, loosen the other screws and adjust the position of unit B.

4)	(CVP-709PWH) Attach two caps K. 

5)	Fasten unit C to unit A in the same way.

3	Attach unit E to unit D.
Fix unit E to unit D using two screws L. 
(Figure)

4	Attach unit D to unit A.

1)	Fix unit D to the bottom surface of unit A using two screws L. 
(Figure)

2)	Fix unit D to the speaker box of unit A using two screws J.
If the screw holes do not align, loosen the other screws and adjust the position of unit D.

3)	(CVP-709PWH) Attach two caps K. 

5	Raise unit A into the upright position.
(Figure)

CAUTION
Be careful not to pinch your fingers.
When you raise the unit, do not hold the key cover.

6	Install unit F.

1)	Remove the cover from unit D.
(Figure)

2)	Untie and straighten out the bundled cord.
(Figure)

3)	Pass the pedal cord from under unit D to the backside of the main unit.
(Figure)

4)	Place unit F on the bracket of unit D.

5	Attach unit F to unit D using three screws M.
(Figure)

7	Connect the pedal cord.
(Figure)

1)	Insert the pedal cord plug into the pedal connector.
Insert the pedal cord securely until the metal part of the cord plug disappears from view. Otherwise, the pedal may not function properly.

2)	Pass the pedal cord between units D and E.

3)	Align the pedal cord into the groove on unit D, then install the cover onto the groove correctly.
Correct
Incorrect

4)	Attach unit G using two screws N.
(Figure)

5)	(CVP-709PWH) Attach two caps K. 

8	Insert the AC power cord plug into the [AC IN] jack.
(Figure)

9	Rotate the adjuster until it comes in firm contact with the floor surface.
(Figure)

10	Attach the headphone hanger.
Attach the headphone hanger using two screws P as shown in the illustration.
(Figure)

After completing the assembly, please check the following.

Are there any parts left over?
Review the assembly procedure and correct any errors.

Is the instrument clear of doors and other movable fixtures?
Move the instrument to an appropriate location.

Does the instrument make a rattling noise when you shake it?
Tighten all screws.

Does the pedal box rattle or give way when you step on the pedals?
Turn the adjuster so that it is set firmly against the floor.

Are the pedal and power cords inserted securely into the sockets?

CAUTION
When moving the instrument, always hold the bottom of the main unit. Do not hold the key cover or top portion. Improper handling can result in damage to the instrument or personal injury.
(Figure)
Hold here.
Do not hold here.

Transporting
If you move to another location, you can transport the instrument along with other belongings. You can move the unit as it is (assembled) or you can disassemble the unit down to the condition it was in when you first took it out of the box. Transport the keyboard horizontally. Do not lean it up against a wall or stand it up on its side. Do not subject the instrument to excessive vibration or shock. When transporting the assembled instrument, make sure all screws are properly tightened and have not been loosened by moving the instrument.

CAUTION
If the unit creaks or is otherwise unsteady when you play on the keyboard, refer to the assembly diagrams and retighten all screws.

This is the end of the file.