MODUS
H11
Owner's Manual

Keyboard Stand Assembly

CAUTION
Be careful not to confuse parts, and be sure to install all parts in the correct direction. Please assemble the unit in the appropriate sequence.
Assembly should be carried out by at least two persons.
Be sure to use the included screws only, and insert screws of the correct size in the correct hole locations. Do not use any other screws. Use of incorrect screws can cause damage or malfunction of the product.
Be sure to tighten all screws upon completing assembly of each unit.
To disassemble, reverse the assembly sequence.

Have a Phillips-head (plus) screwdriver ready.

Remove all parts from the box. Confirm that all parts shown in the illustration are provided.

CAUTION
Be careful not to pinch your fingers when setting the instrument on the floor.

(Figure)
A, B, C, D, E, F
6 x 30 mm long screws  x 4
6 x 20 mm short screws  x 10
4 x 6 mm small screws  x 6
Cord holders  x 4
You can attach the included cord holders and tuck in the LAN cable to suit your setup situation.
Before starting installation, remove the vinyl ties that bundle the pedal cord and AC power cord.
Remove two rectangle pads (800 x 130 mm) from the packing box.

1.	Place A on top of the pads.

1-1	Locate two pads (F) so that they will be positioned about 30 cm inside from the left and right edges of A.

1-2	Place A on top of the pads.

(Figure)
CAUTION
Do not position the pad under the control panel.
30 cm
pads
30 cm

2.	Raise A to the vertical position.

2-1	Raise A to the vertical position, with the keyboard side on the bottom, and hold A securely.

(Figure)
CAUTION
Do not release A until you finish Step 4.

CAUTION
Do not tip A further than 90 degrees to avoid stress to the key cover and lid.

3.	Attach B.

3-1	Align the holes on A with those on B and hold A and B together.

3-2	Finger-tighten six short screws (6 x 20 mm) starting with the top hole.

3-3	Tighten the screws securely.

4.	Attach C. 

4-1	Align the holes on A with those on C and hold A and C together.

4-2	Finger-tighten four short screws (6 x 20 mm) starting with the top hole.

4-3	Tighten the screws securely.

5.	Assemble the pedal structure.

5-1	Pass the pedal cord (that comes out from the rear of pedal box E) through a hole on the bracket of D, then pass it through the pipe.

5-2	Align the holes on the bottom of E with the holes on the bracket of D, then attach E and D by tightening six small screws (4 x 6 mm). At this time, first tighten the two center screws, then tighten the rest of the screws.

5-3	Pull the end of the pedal cord to eliminate any slack inside the bracket on D.

CAUTION
Hold E securely to avoid slippage.

6.	Install the pedal structure.

6-1	Remove the covers from the grooves on the bottom surface of A.

6-2	Align the pedal power cords (that come out from the pipes of D) along with the grooves on the bottom surface of A.

6-3	Align the holes on the bracket of D with the holes on A, then attach D to A by tightening four long screws (6 x 30 mm).

CAUTION
Be careful not to pinch the cords between the bracket and the surface of A.

7.	Connect the cords.

7-1	Connect the pedal cord plug to the pedal connector in the correct orientation.

7-2	Set the voltage selector to an appropriate voltage.

7-3	Connect the power cord plug to the power connector in the correct orientation.

Voltage Selector
Before connecting the AC power cord, check the setting of the voltage selector which is provided in some areas. To set the selector for 110V, 127V, 220V or 240V main voltages, use a "minus" screwdriver to rotate the selector dial so that the correct voltage for your region appears next to the pointer on the panel. The voltage selector is set at 240V when the unit is initially shipped. After the proper voltage has been selected, connect the AC power cord to the AC IN and an AC wall outlet. A plug adaptor may be also provided in some areas to match the pin configuration of the AC wall outlets in your area.

8.	Replace the groove covers.
8-1	Insert the pedal cord and power cords into the grooves securely, then attach the groove covers.

(Figure)
Correct
Incorrect

9.	Raise A.
9-1	Securely hold the front side of A (the side currently facing toward the floor), then raise A.

CAUTION
Do not hold the control panel area.
Be careful not to drop the instrument on your foot.

10.	 Rotate the adjuster.
10-1	Rotate the pedal height adjuster until the bottom of the pedal reaches the floor.

You can attach the included cord holders and tuck in the LAN cable to suit your setup situation.

After completing the assembly, please check the following.
Are there any parts left over?
->	Review the assembly procedure and correct any errors.
Is the instrument clear of doors and other movable fixtures?
->	Move the instrument to an appropriate location.
Does the instrument make a rattling noise when you shake it?
->	Tighten all screws.
Does the pedal box rattle or give way when you step on the pedals?
->	Turn the adjuster so that it is set firmly against the floor.
Are the pedal and power cords inserted securely into the sockets?
->	Check the connection.

CAUTION
If the main unit creaks or is otherwise unsteady when you play on the keyboard, refer to the assembly diagrams and retighten all screws.

CAUTION
When you relocate the unit after assembling it, be sure to hold the bottom of the main unit. In particular, hold the left side of the main unit along with the bottom of the upper frame of the left leg.

(Figure)
CAUTION
Do not hold the key cover or lid.

CAUTION
Do not hold the control panel area.
Be careful not to drop the instrument on your foot.

This is the end of the file.