Keyboard Stand Assembly.
CAUTION.
Be careful not to confuse parts, and be sure to install all parts in the correct direction. Please assemble in accordance with the sequence given below.
Assembly should be carried out by at least two persons.
Be sure to use the correct screw size, as indicated below. Use of incorrect screws can cause damage.
Be sure to tighten up all screws upon completing assembly of each unit.
To disassemble, reverse the assembly sequence given below.

Have a Phillips-head (plus) screwdriver ready.

Remove the following parts from the package.

Assembly Parts.
1. 6 x 20 mm long screws x4  
2. 6 x 16 mm short screws x4 
3. 4 x 12 mm thin screws x2  
4. 4 x 20 mm tapping screws x4  
Cord holders x 2

Main unit.
Side panel (left)
Side panel (right)
Rear panel.
Pedal box.
Bundled pedal cord inside.
AC power cord.

TIP.
A headphone hanger is included in the YDP-123 package. You can attach a headphone hanger on the YDP-123 to hang the headphones (page 12).

1.	Attach the side panels to the pedal box.
(Figure)
(1)	Untie and straighten out the bundled cord attached to the bottom of the pedal box. 
Don't discard the vinyl tie, you'll need it later in step 5.
(2)	Align the sides of the pedal box with the left and right side panels.
(3) Use the four 6~20 mm long screws 1 to attach the pedal box.

2. Attach the rear panel.
(Figure)
(1)	Secure the top of the rear panel to the side panel brackets using two 4x12 mm thin screws 3.
(2) 	Secure the bottom of the rear panel to the pedal box using four 4 x 20 mm tapping screws 4 .

3. Mount the main unit.
CAUTION.
Fingers can become pinched between the main unit and the rear or side panels, be extra careful so as not to drop the main unit.
Do not hold the keyboard in any position other than the position shown in the illustration.
(Figure)
Be sure to place your hands at least 10 cm from either end of the main unit when positioning it.

4.	Fix the main unit.
(Figure)
(1) Center the main unit to pro-duce equal clearance on the left and right sides.
(2) Use 6x16 mm short screws 2 to secure the main unit from the front.

5.	Connect the pedal cord.
(Figure)
(1) Insert the pedal cord plug to the pedal connector from the rear.
(2) Attach the cord holders to the rear panel as shown, then clip the cord into the holders.
(3) Use a vinyl tie to take up any slack in the pedal cord.

6.	Set the voltage selector and connect the power cord.
(Figure)
Voltage Selector.
Before connecting the AC power cord, check the setting of the voltage selector which is provided in some areas. To set the selector for 110V, 127V, 220V or 240V main voltages, use a "minus" screwdriver to rotate the selector dial so that the correct voltage for your region appears next to the pointer on the panel. The voltage selector is set at 240V when the unit is initially shipped. After the proper voltage has been selected, connect the AC power cord to the AC INLET and an AC wall outlet. A plug adaptor may be also provided in some areas to match the pin configuration of the AC wall outlets in your area.

WARNING
An improper voltage setting can cause serious damage to the YDP-123 or result in improper operation.

7.	Set the adjuster.
Rotate the adjuster until it comes in firm contact with the floor surface.

After completing the assembly, please check the following.
Are there any parts left over?
->	Review the assembly procedure and correct any errors.
Is the YDP-123 clear of doors and other movable fixtures?
->	Move the YDP-123 to an appropriate location.
Does the YDP-123 make a rattling noise when you shake it?
->	Tighten all screws.
Does the pedal box rattle or give way when you step on the pedals?
->	Turn the adjuster so that it is set firmly against the floor.
Are the pedal and power cords inserted securely into the sockets?
->	Check the connection.
If the main unit creaks or is otherwise unsteady when you play on the keyboard, refer to the assembly diagrams and retighten all screws.

When moving the instrument after assembly, always hold the bottom of the main unit.

CAUTION.
Do not hold the key cover or top portion. Improper handling can result in damage to the instrument or personal injury.

Index is not available.

Appendix
This section introduces reference material.

MIDI Data Format is not available.
MIDI Implementation Chart is not available.


This is the end of the file.